NEO20S Hook
We’ve made the NEO20S 15mm slimmer, (by rearranging the position of its motor), and this has given the NEO20S an additional 60mm in height clerance. This is ideal when the lifting point has a very narrow opening and its contact point is lower than usual. With its 20,000 kgs. (44,092 lbs.) lifting capacity, it is ideal for oversized lifting points of up to 100mm (Ø)
20,000 kgs./44,092 lbs. lifting capacity
Ideal for oversized lifting points (up to 90mm Ø)
Remote engage and release of load
Fail-safe Design: Impossible to drop a suspended load
Safety factor of 4:1
Check out all of our NEO Heavy Duty Lifting Hooks
Check it out!
In Detail
Swivel with Bearings
The bearings allow the NEO20S hook to rotate freely.
If required, the swivel can be set in a fixed position.
LED Status Indicator
The High-Brightness LED status indicator is an additional safety measure which shows the hook’s
status at all times with a bright 4 colour colour-code scheme visible from the operator’s position.
The pulse of the LED status indicator takes an intermittent
pattern after 10 seconds in order to save battery.
Green: Lifting Hook is Open / Release Load
Red: Intermediate: Do Not Lift!
Blue: Lifting Hook is Closed / Lift & Manoeuvre Load
White: Low Battery
Smart Battery
With the high-capacity battery, a simple 3 hour charge allows for
more than 3.000 cycles or over 250 hours in standby mode.
By means of the eMAX remote control, the electronics of the lifting hook
can be configured so that when the battery charge is below
a preset threshold by the user, the hook can only be opened.
With this threshold, even if the battery is almost discharged,
you will always be able to open the lifting hook and release the load.
Load Cell *
The NEO20S carries a precise load cell.
It is fully integrated into the lifting hook, representing
no increase in weight or dimensions of the unit.
With the load cell, and should there be a suspended load on the hook,
the intermittence of the LED status indicator’s pulse is of higher frequency.
* This feature is optional
Specifications
| Load Cell Type | Traction |
| Material | Stainless Steel |
| Protection | IP67 (EN60529) |
| Nominal Capacity (Ln) | 20,000 |
| Precision Class | 0.2% |
| Minimum Dead Load | 0% Ln |
| Service Load | 120% Ln |
| Ultimate Load | 400% Ln |
| Total Error | < ±0.2% Sn |
| Repeatability Error | < ±0.08% Sn |
| Temperature Effect: | |
| on zero | < ±0.01% Sn / 5 ºK |
| on sensitivity | < ±0.01% Sn / 5 ºK |
| Creep Error (30 min.) | < ±0.03% Sn |
| Temperature Compensation | -4 ºF to 122 ºF |
| Temperature Limit | -22 ºF to 158 ºF |
| Nominal Sensivity (Sn) | 1 ±0.25% mV/V |
| Nominal Input Voltage | 10V |
| Maximum Input Voltage | 15V |
| Input Impedance | 800 ±30 |
| Output Impedance | 700 ±5 |
| No Load Input | < ±2% Sn |
| Insulation Resistance | > 5,000 M |
| Maximum Deflection (at Ln) | 0.3 mm. |
Autoclose Mode
A contact sensor detects when the hook is closed,
and NEO20S closes automatically.
Laser Pointer *
As an optional feature, the NEO20S carries a Laser Pointer.
It acts as a guide to perfectly place and set the lifting hook
in the correct position when approaching the lifting point.
To activate it, simply press the button beside the battery slot.
* This feature is optional
Remote Controlled
At elebia, we produce different remote controls tailored to our customer’s needs.
All of them allow simple, flexible, precise and reliable control in a fail-safe way.
The NEO20S can be paired to either the eMAX, eMINI or eINST
remote controls, or to all 3 if necessary.
Fail-safe Designed
Just like the rest of the NEO range of lifting hooks,
(and all of our lifting products for that matter)
the NEO20S hook is designed under a fail-safe principle
that makes it impossible to drop a suspended load.
Manual Override
If there’s ever the need to manually override NEO20S’s
electronics, the process is very simple.
1. Insert the end/tip of pole in the cover’s slot.
2. Lower the end/tip of pole until it reaches
the narrow lower bottom end of the cover’s slot.
3. Pull until the cover opens and wait until LEDs turn green.
Regulatory Standards 
The NEO20S hook certifies with the following regulatory standards:
| ETSI EN 303 446-1 V1.1.0 | EN 10204 3.1.B | UNE-EN 60730-1:2013 |
| ETSI EN 303 446-2 V1.1.0 | UNE-EN ISO12100:2012 | UNE-EN 61000-6-4:2007 |
| ETSI EN 300 220-1 V3.1.1 | UNE-EN 1050 | UNE-EN 61000-6-2:2006 |
| ETSI EN 300 220-2 V3.1.1 | UNE-EN 13135:2013 | UNE-EN 60204-1:2007 |
Directive on Machine Safety (D2006/42/EC).
EMC Directive (2014/30/EU).
Low Voltage Directive (2014/35/EU).
Radio Equipment Directive (2014/53/EU).
Assurance of Production Quality in accordance with ISO9001.
ARIB Construction Design Certification Number 203-JN0689.
FCC Identifier 2ACLHEVO for Equipment Class: Digital Transmission System.
Each mechanism is delivered with the CE stamp and a declaration of CE conformity.
elebia is a member of F.E.M. (European Federation of Materials Handling).
See it in Action!
Lifting Procedure
LED Status Indocator
Quick Links
Configurator
Personalize and configure
your NEO20S lifting hook
and its accessories.
Schedule a Demo
Need or want to see in person
how your company can benefit
by using the NEO20S lifting hook?
User Manual
All the info you need and
more, of the NEO20S lifting
hook for bell furnaces.
Quotation
Receive a quote for your
NEO20S lifting hook or any other
product and accessory.
(+34) 93 543 4706
info@elebia.com
